Sure-heat Sonoma SGR27 Natural Gas Conversion Kit Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Sure-heat Sonoma SGR27 Natural Gas Conversion Kit. Sure Heat Sonoma SGR27 Natural Gas Conversion Kit User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 8
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
S
S
o
o
n
n
o
o
m
m
a
a
S
S
o
o
n
n
o
o
m
m
a
a
PLA
PLA
TINUM
TINUM
EDITION
EDITION
TM
27" Natural Gas Conversion Manual
FOR OUTDOOR USE ONLY
Part No. Qty Description
1
44213827 1 Hose 27" - 3/8" Flare Both Ends for Side Burner (NG)
2
40275101
1
Main Burner
Valve & Manifold Assembly with Valves (NG)
3 44110102 2 Connector 3/8" MNPT x 3/8" Flare
4 44133801 1 Tee Fitting - Galvanized 3/8" Flare
5 49900004 1 Sealant Pipe (4ml)
6 44183815 1 Nipple Pipe 3/8" NPT x 1.5"
7 47311010 1 Regulator 3/8" FNPT Threads (NG)
8 46210102 1 Side Burner Valve Assembly - 12K BTU (NG)
9 08338381 1 3/8" Street Elbow
8
7
6
5
4
3
2
1
CANADIAN GAS ASSOCIATION
APPROVED
®
9
Zobrazit stránku 0
1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - FOR OUTDOOR USE ONLY

SSoonnoommaaSSoonnoommaaPLAPLATINUMTINUMEDITIONEDITIONTM27" Natural Gas Conversion ManualFOR OUTDOOR USE ONLYPart No. Qty Description144213827 1

Strany 2 - Adjustable wrench

Be sure gas supply is off, the knobs are in the offposition and the grill is cool.1. Remove cooking grates and flavor grids. (See Fig. 1)2. Remove the

Strany 3

7. Remove the front heat shield. (See Fig. 7)8. Grasp and push the burner(s) towards the rear ofthe grill to detach the burner from the valves.(See Fi

Strany 4

You are now ready to install the new NG manifold.15. Start by placing the new manifold into the grillbody with the control knob stems going outwardthr

Strany 5

Installing the NG regulator1. Remove the LP regulator from the main gas pipeusing an adjustable wrench. Located inside thecart on bottom of grill head

Strany 6

5. Attach the 3/8” to flared fitting to the “T” fitting asshown. Remember to apply pipe dope to thenon-flared end. Tighten with wrench. (See Fig. 22)6

Strany 7

Converting the Side Burner to NG1. Remove side burner grate, porcelain cap andburner head. (See Fig. 28)2. Remove the LP regulator hose attached to th

Strany 8

6. Install the NG valve assembly to the under side of the side burner with the two (2) screws previously removed. (See Fig. 33).Note: Make sure the NG

Komentáře k této Příručce

Žádné komentáře